Axopar 37 ST Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 44

Axopar 37 ST Скачать руководство пользователя страница 24

Copyright @ Aivan Oy

Axopar
Axopar 37

Drawing:

Axopar 37 CTT

Scale:

Date:

1:50

27.11.2015

Aivan Oy

Laivakatu 3

00150 Helsinki, Finland

+358 (0)10 423 6401

[email protected]

www.aivan.fi

Axopar 37 TT

3.4.1 LIFTING AND TRANSPORTING

LIFTING

Position the lifting straps as shown in the picture below. When the straps have
been attached to the lifting hook on the crane they should be secured with lines
to the bow and stern cleats to prevent the lifting straps from sliding.

TRANSPORTING

Always use an authorized boat transport company for transporting the boat on
land. Make sure the company has full insurance cover, in case of any damages.

The lifting beam should be exactly the same width as the boat. Always
take great precautions near and around the boat when lifting. Note
the location of the log transducer to avoid damaging it. Protect the hull
sides well to avoid damages. The position of the slings may need to be
adjusted depending on how the boat is loaded.

CAUTION!

24

«
...
22
23
24
25
26
...
»

Содержание 37 ST













































Отзывы:

Нет отзывов