manualshive.com logo in svg

Axopar 37 ST, Руководство пользователя, Страница: 14 / 44

Поделиться
Скачать
Axopar 37 ST Скачать руководство пользователя страница 14

2.4 BILGE PUMP SYSTEM

The bilge pump system consists of several different pumps that cover all the 
lower sections of the boat. Both electric and manual bilge pumps have been 
installed. The boat also has a sign that displays the draining area of each pump. 
The electric bilge pumps are equipped with a float which triggers them automat

-

ically if there is water in the bilge space. The pumps can also be controlled from 
switches (5) on the steering console. The automatic bilge pumps are equipped 
with an alarm signal which is activated when the pump starts.

The manual bilge pump (1) is controlled with its handle, which is located in the 
port  side  stowage  casing  of  the  afterdeck.  The  purpose  of  the  manual  bilge 
pump is to drain the tank space.

The electric pumps are submersible. One of them is located under the berth of 
the aft cabin (2), another under the toilet seat (3) and a third under the berth in 
the fore cabin (4). The bilge water level should remain at a minimum. 

The output of each automatic bilge pump is 41 litres per minute. The manual 
bilge pump’s output is 33 litres per minute. 

1

2

3

5

4

Check the functionality of the bilge pumps regularly. Remove any waste 
from the intakes. The combined capacity of the bilge pump system is 
not designed to pump out the boat in the event of hull damage. The 
pumps are constantly activated and pump out the boat as required. 
The pumps can also be started manually from the boat’s main control 
panel.

DANGER!

Avoid  pollution!  The  purpose  of  the  boat’s  electrical  bilge  pumps  is   
to minimize the risk of accidental discharge of oil polluted water. The 
boat owner should check the bilge water regularly for contaminants 
such as oil, diesel, glycol etc. The bilge pump system comprises several 
different pumps that cover all areas of the boat. Your boat has elec

-

trical as well as manual bilge pumps. There is also a sign in the boat 
indicating the draining area of each pump  respectively.

CAUTION!

The pumps must not be run dry for any length of  time.

CAUTION!

14

Содержание 37 ST













































Отзывы:

Нет отзывов