background image

1. General Safety Rules 

WARNING

 

 

1.  Read and understand instructions of this 

manual entirely before operating the 

machine. 

 
2.  Always wear approved safety glasses 

/face shields when using the machine. 

 
3.  Make certain the machine is properly 

grounded. 

 
4.  Before machine in operation, remove ties, 

rings, watches, other jewelry, and roll 

your sleeves up to above elbows. 

Remove loose clothing and confine long 

hair. 

 
5.  Keep the floor around this machine clean 

and free of scrap material, oil and grease. 

 
6.  Keep machine guards in place at all 

times when the machine is in use. If it 

removed for maintenance purpose, pay 

extra attention and replace these guards 

at once. 

 
7.  Do not over reach. Keep a balanced 

stance all the time so that your don’t fall 

lean against blade or some other moving 

parts. 

 
8. Whenever make any adjustments or 

maintenance with the machine must 

unplugged the power source 

 
9.  Use the right tool. Don’t force a tool or 

attachment to do a job that it was not 

designed for. 

 
10. Replace warning labels if they have   

 

 

become obscured or removed. 

 
11. Make certain the motor switch is in 

off

 

position while connecting the machine 

into the power supply. 

 
12. 

Pay your work undivided attention. 

Looking around, and carrying on a 

conversation, or 

horse-play

”  

are 

careless acts which might result in 

serious injury. 

 
13. Keep visitors a safe distance from the 

work area. 

 
14. Use  recommended  accessories,  and 

parts. Improved accessories may be 

hazardous. 

 
15. Form the good habit of checking to see 

keys and wrenches are removed before 

turning on this machine, 

 
16. Always keep hands & fingers away from 

the black when this machine is running. 

 
17. Never hold a material with this saw in the 

horizontal position. Please be sure 

always use the vise to clamp it securely. 

 
18. 

Read and understand warnings that 

posted on the machine. 

 
19. Always provide necessary support for 

long and heavy material 

 
20. Use a sharp blade and always keep 

machine clean for a best and safest 

performance. 

 
21. Failure to comply with any of these 

warnings may cause serious injury. 

 

 

Содержание MCB100A





















Отзывы: