Axminster AS408 Скачать руководство пользователя страница 24

Страница: 24 / 28

W H I T E

A X M I N S T E R

Troubleshooting...

Motor will not run.

1. Defective or broken

“ON -OFF” switch.

2. Defective or damaged

switch cord.

3. Defective or damaged

switch relay.

4. Burned out motor.

5. Blown fuse.

1-3. Replace all broken or

defective parts before using
the sander.

4. Contact Axminster Tool
Centre on 0800 371822 &
asked to be transferred to
the“Technical Sales”
department.

Machine slows down while

sanding.

1. Applying to much pressure

to workpiece.

1. Apply less pressure to

sanding surface.

Sanding belt runs off pulleys. 1. Belt NOT tracking properly. 1. Adjust tracking (See page

21) on how to track the belt.

Wood burns while sanding.

1. Sanding disc or belt is

worn.
2. Excessive pressure being
applied to workpiece.

1. Replace the disc or belt.

2. Reduce pressure being
applied to workpiece.

PROBLEM

POSSIBLE CAUSE

REMEDY

Wiring Diagram

Содержание AS408





























Результаты поиска

Содержание AS408

Отзывы:

Бренды по названию

Популярные бренды

Axminster AS408, Руководство пользователя

Результаты поиска

Содержание AS408

Отзывы:

Бренды по названию

Популярные бренды