Axminster Trade 106202 Скачать руководство пользователя страница 2

Страница: 2 / 28

Index of Contents

EU Declaration of Conformity

EU Declaration of Conformity

What’s Included

General Instructions for 230V Machines

Specific Precautions Using Thicknessers

Specification

Assembly

Machine Dimensions

Illustration and Parts Description

08-09-10-11-12

Positioning the Machine

Operating Instructions

14-15

Maintenance

16-17-18-19

Exploded Diagram/Parts List

20-21-22-23

Wiring Diagram

Notes

25-26-27

Cert No: MB103

Axminster Tools & Machinery Ltd
Axminster Devon
EX13 5PH UK
axminster.co.uk

Type

Thicknesser

Model

AT310T2

and conforms to the machinery example for which the
EC Type-Examination Certificate No BM 50314336, AE 50390663
has been issued by Laizhou Planet Machinery Co., Ltd.
at: Yutai West Street Laizhou, Shandong 261400 China (Mainland)

and complies with the relevant essential health and safety requirements.

2006/42/EC
2014/30/EU
06/42/EC - Annex I/05.2006
EN 60204-1:2006+A1+AC
EN 861:2007+A2
EN 61000-3-3:2013

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

EN 55014-1:2006+A1+A2
EN 55014-2:1997+A1+A2
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014

Signed

Andrew Parkhouse
Operations Director

Date: 29/06/2015

The symbols below advise the correct safety procedures when using this machine.

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Dust mask

should be worn

Содержание 106202





























Результаты поиска

Содержание 106202

Отзывы:

Бренды по названию

Популярные бренды

Axminster Trade 106202, Оригинальное руководство пользователя

Результаты поиска

Содержание 106202

Отзывы:

Бренды по названию

Популярные бренды