Axis P5635-E Mk II, Руководство по установке

Страница: 4 / 24

English
Safety Information
Read through this Installation Guide carefully before
installing the product. Keep the Installation Guide for
future reference.
Hazard Levels
DANGER
Indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NO NO NOTICE TICE TICE
Indicates a situation which, if not avoided, could result in
damage to property.
Other Message Levels
Important
Indicates significant information which is essential for the
product to function correctly.
Note
Indicates useful information which helps in getting the
most out of the product.
Safety Instructions
NO NO
NOTICE
TICE
TICE
•
The Axis product shall be used in compliance with local
laws and regulations.
•
Store the Axis product in a dry and ventilated
environment.
•
Avoid exposing the Axis product to shocks or heavy
pressure.
•
Do not install the product on unstable brackets, surfaces
or walls.
•
Use only applicable tools when installing the Axis
product. Using excessive force with power tools could
cause damage to the product.
•
Do not use chemicals, caustic agents, or aerosol cleaners.
•
Use a clean cloth dampened with pure water for
cleaning.
•
Use only accessories that comply with technical
specification of the product. These can be provided by
Axis or a third party.
•
Use only spare parts provided by or recommended by
Axis.
•
Do not attempt to repair the product by yourself.
Contact Axis support or your Axis reseller for service
matters.
•
Do not point the camera lens toward the sun or other
high-intensity radiation sources because this could
cause damage to the camera.
•
The power supply shall be plugged in to a socket outlet
installed near the product and shall be easily accessible.
•
Use a limited power source (LPS) with either a rated
output power limited to <100 W or a rated output
current limited to <5 A.
Transportation
NO NO
NOTICE
TICE
TICE
•
When transporting the Axis product, use the original
packaging or equivalent to prevent damage to the
product.
Battery
The Axis product uses a 3.0 V BR2032 lithium battery as the
power supply for its internal real-time clock (RTC). Under
normal conditions this battery will last for a minimum of
five years.
Low battery power affects the operation of the RTC, causing
it to reset at every power-up. When the battery needs
replacing, a log message will appear in the product’s server
report. For more information about the server report, see
the product´s setup pages or contact Axis support.
The battery should not be replaced unless required, but if
the battery does need replacing, contact Axis support at
www.axis.com/techsup for assistance.
WARNING
•
Risk of explosion if the battery is incorrectly replaced.
•
Replace only with an identical battery or a battery which
is recommended by Axis.
•
Dispose of used batteries according to local regulations
or the battery manufacturer's instructions.
Dome Cover
NO NO NOTICE TICE TICE
•
Be careful not to scratch, damage or leave fingerprints
on the dome cover because this could decrease image
quality. If possible, keep the protective plastic on the
dome cover until the installation is complete.
•
Do not clean a dome cover that looks clean to the eye
and never polish the surface. Excessive cleaning could
damage the surface.
•
For general cleaning of the dome cover it is
recommended to use a non-abrasive, solvent-free
neutral soap or detergent mixed with pure water and a
soft, clean cloth. Rinse well with pure lukewarm water.
Dry with a soft, clean cloth to prevent water spotting.
•
Never use harsh detergents, gasoline, benzene or
acetone etc. and avoid cleaning the dome cover in direct
sunlight or at elevated temperatures.
•
Make sure the dome is attached in operation mode,
otherwise focus may be affected.