manualshive.com logo in svg

Axis DIGITAL LINE L06DUS, Инструкция по установке и эксплуатации

Поделиться
Скачать
Axis DIGITAL LINE L06DUS Скачать руководство пользователя страница 44

44

Maintenance

1

GENERAL CLEANING WARNINGS

Disconnect the appliance power supply and wear adequate personal protective equipment (e.g. gloves) before 
performing any cleaning.

The user must only perform routine cleaning. Contact an authorised service centre to request the assistance of a 
specialist, suitably trained technician for inspection work, special maintenance and replacement of any defec-
tive parts.
During the warranty period, the manufacturer does not recognise damage deriving from a lack of maintenance 
or incorrect cleaning (e.g. use of unsuitable cleaning agents).

Before performing any cleaning work, wait for the cooking cavity to cool (temperature not above 140°F).

When cleaning any part of the appliance or accessory 

DO NOT

 use:

 -abrasive or powder detergents;
 -aggressive or corrosive detergents (e.g. hydrochloric/muriatic acid, sulphuric acid, caustic soda, etc.). Warning! Never use these 

substances when cleaning the appliance substructure or the floor under the appliance;

 -abrasive or sharp tools (abrasive sponges, scrapers, steel-bristled brushes, etc.);
 -steam or pressurised water jets.

Refer to the drawing on page 

45

 for information on how to correctly clean each appliance component.

 

Содержание DIGITAL LINE L06DUS





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды