Axis AXIS 570 Скачать руководство пользователя

Страница: 82 / 316

Section 5: Setting Up - IBM Mainframe

AXIS 5470e/570/670e User’s Manual

NetWare for

SAA Server

To set-up a TN3270E connection to the AXIS 5470e/570/670e you
have to set up PU and LU definitions. This is done by following the
steps below:

1. Start the NWSAA Administrator.

2. Double click on the NWSAA Node. The panel below will appear.

3. Enter the Node ID for the host.

4. Leave the rest at their default settings.

Peer PU profile

5. Click on the TN3270 icon. The panel below will appear.

6. Select All Available Host PU profiles.

7. Enter the user name, from the User List, that you want all

TN3270 clients to use.

8. Specify the maximum number of TELNET connections you want

to allow each TN3270 client.

Содержание AXIS 570





























































































































































































































































































































Результаты поиска

Содержание AXIS 570

Отзывы:

Похожие инструкции для AXIS 570

Бренды по названию

Популярные бренды

Axis AXIS 570, Руководство пользователя

Результаты поиска

Содержание AXIS 570

Отзывы:

Похожие инструкции для AXIS 570

Бренды по названию

Популярные бренды