Axis AXIS 570 Скачать руководство пользователя страница 284 | Manualshive

Страница: 284 / 316

background image

Appendix H: Digital Copier Support

AXIS 5470e/570/670e User’s Manual

284

•

Center 2

i.e. two staples set in the center of the page. This option

is intended for documents printed in A3 format. The staples are
placed in the center of the page where the document is to be
folded. Please refer to the documentation of your digital copier for
more information on these features.

Copier Hole Punch

The AXIS 5470e/670e supports hole punching with the following options:

•

Off

i.e. the hole punching option is not activated (default).

•

Long-edge

i.e. the left hand side of the document.

•

Short-edge

i.e. the top of the document.

Copier Paper Source

Enter the desired input bin i.e. paper tray on your digital copier

Copier Copies

Enter how many collated (sorted) copies you wish to print in the

Copies

field.

Notes:

•

The options are all available in the drop-down lists under Model, Duplex, Sta-
ple, Punch, Paper Source and Copies. However, you must refer to the docu-
mentation of your specific Digital Copier to check that all the options are
supported.

•

If you experience problems with this functionality the Digital Copier printing
options may have been set inconsistently. Please check your configuration
settings and try again.

«
...
282
283
284
285
286
...
»

Содержание AXIS 570





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AXIS 570

Бренд: IBM Страницы: 151

Бренд: CAB Страницы: 263

Бренд: EBS Страницы: 4

Бренд: NCR Страницы: 38

Бренд: Samsung Страницы: 165

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 319

Бренд: Oki Страницы: 45

Бренд: Vxl Страницы: 19

Бренд: DNP Страницы: 66

Бренд: TYAN Страницы: 64

Бренд: Eaton Страницы: 2

UltraNEXUS-HD X5

Бренд: Leightronix Страницы: 5

Accel a Writer 812

Бренд: Xante Страницы: 312

ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER

Бренд: Novell Страницы: 390

Бренд: Supermicro Страницы: 118

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

VERSAJET MP3200 Series

Бренд: Cino Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды