Axis AXIS 570 Скачать руководство пользователя страница 228

Страница: 228 / 316

Section 14: Upgrading the software

AXIS 5470e/570/670e User’s Manual

228

Upgrading the firmware Software

You can upgrade the AXIS 5470e/570/670e Flash memory using one
of the following methods:

•

AXIS ThinWizard (TCP/IP)

•

FTP (TCP/IP)

•

AXIS NetPilot Upgrade Wizard (IPX/SPX)

Note:

Upgrading using

AXIS ThinWizard

AXIS ThinWizard is a tool that enables batch upgrading of several
print servers and should be used for upgrading the flash memory in
TCP/IP networks.

You must assign the AXIS 5470e/570/670e with an IP address, as
described in

Assigning an IP address,

on page 32, before you can use

this upgrading method.

Follow the instructions below to upgrade your print servers using
AXIS ThinWizard:

1. Click the

Manage Network

button in the AXIS ThinWizard

main menu.

2. Select a network group from the drop-down list. You can only

update the servers that are included in the selected network group.

3. All AXIS servers included in the network group appear. Click the

Firmware

button to start the Upgrade Wizard.

4. Follow the instructions that are presented to you to complete the

installation.

Refer to

Using AXIS ThinWizard

, on page 175, for more information

about AXIS ThinWizard.

Updating instructions are also supplied with the software update.

Содержание AXIS 570





























































































































































































































































































































Результаты поиска

Содержание AXIS 570

Отзывы:

Похожие инструкции для AXIS 570

Бренды по названию

Популярные бренды

Axis AXIS 570, Руководство пользователя

Результаты поиска

Содержание AXIS 570

Отзывы:

Похожие инструкции для AXIS 570

Бренды по названию

Популярные бренды