Axis AXIS 570 Скачать руководство пользователя страница 64

Страница: 64 / 316

Section 4: Setting Up - AS/400

AXIS 5470e/570/670e User’s Manual

Verifying the

communication

Follow the instructions below to verify the communication by sending
a print job to the AXIS 5470e/670e:

Note

1. Type

WRKCFGSTS *DEV AXISPR1

on the AS/400 command

line and press

Enter

to display the previously created printer

device. The status of the printer device should be

VARIED OFF

2. Vary on the printer device by typing

in the

Opt

field. Press

NTER

3. Press

to refresh the display. The printer device should now be

VARIED ON

4. Start the printer writer by typing

STRPRTWTR AXISPR1

the AS/400 command line. Press

Enter

5. Press

to refresh the display. The printer device should now be

ACTIVE/WRITER

6. Direct a printout to this printer device. A successful printout

verifies the communication link between the AS/400 and the
AXIS 5470e/670e.

The AXIS 5470e/670e is now ready for printing in the AS/400
environment.

AXISPR1

is an example. Refer to

Creating a Printer Device Description

on page 59

for details

Содержание AXIS 570





























































































































































































































































































































Результаты поиска

Содержание AXIS 570

Отзывы:

Axis AXIS 570, Руководство пользователя, Страница: 64 / 316

Результаты поиска

Содержание AXIS 570

Отзывы: