background image

 

Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0

 

Once installed properly, your AWE exhaust will provide years of trouble

-

free performance.

 

 

The exhaust volume and sound will settle with usage; 800

-

1000 miles is required to break

-

in new 

exhaust systems.

 

 

Also, please note that the rear 

180Technology®

 resonator has a small drain hole to allow 

condensation to escape. Water drops from this area are normal.

 

 

Periodic cleaning of exhaust tips is necessary to maintain proper finish, especially in areas prone to 

road salt and caustic deicing solutions. Use a mild soap and water solution or car wax to clean the 

finish. Avoid using abrasive polishes, as they can scratch the finish. 

 

Up

-

to

-

date warranty information is found 

HERE

.

 

 

 

Any questions or comments, 

 

please do not hesitate to contact us:

 

 

 

AWE

 

199 Precision Drive

 

Horsham, PA 19044

 

 

215

-

658

-

1670

 

CONTACT FORM

 

Issue

 

Solution

 

Wrong or missing parts

 

Double check the parts list for your system and compare them 

with what you received. Fill out our contact form, found below 

and let us know what parts you need. 

 

Check engine light

 

Make sure all hoses are reinstalled and are all secure. 

 

Содержание S-FLO











Отзывы: