AVYCON AVC NBL21M-L1 Скачать руководство пользователя страница 12

Страница: 12 / 65

Router Setup

④

Open the IE browser and enter its WAN IP and http port to access. (For example,

if the http port is changed to 81, please enter “192.198.1.201:81” in the address bar of

web browser to access).



Access through PPPoE dial-up

Network connection

Access the camera through PPPoE auto dial-up. The setup steps are as follow:

①

Go to Config



Network



Port menu to set the port number.

②

Go to Config



Network



TCP/IP



PPPoE Config menu. Enable PPPoE and then

enter the user name and password from your internet service provider.

③

Go to Config



Network



DDNS menu. Before configuring the DDNS, please

apply for a domain name first. Please refer to DDNS configuration for detail
information.

④

Open the IE browser and enter the domain name and http port to access.



Access through static IP

Содержание AVC NBL21M-L1


































































Результаты поиска

Содержание AVC NBL21M-L1

Отзывы:

Похожие инструкции для AVC NBL21M-L1

Бренды по названию

Популярные бренды

AVYCON AVC NBL21M-L1, Руководство пользователя

Результаты поиска

Содержание AVC NBL21M-L1

Отзывы:

Похожие инструкции для AVC NBL21M-L1

Бренды по названию

Популярные бренды