Avnet PicoZed FMC V2 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 42

background image

34

22 Sept 2016

v1.1

3.5 JP1 – FPGA VBAT (VCCBATT)

JP1 is a non-populated 100 mil dual pin connector. Use this connection to provide battery
backup power for the FGPA’s internal volatile memory that stores the key for the AES
decryptor. If using this connection, the SOM will require a resistor to be removed. Please see
the appropriate SOMs User Guide (choose the latest revision):

http://picozed.org/support/documentation/4736

NOTE: The voltage input to this connector MUST NOT EXCEED 2.0V or FPGA damage may
result. This connection should be to a power supply or 1.5V battery. The positive voltage is
attached to pin 1, labeled “+BAT”. Ground is attached to pin 2, labeled “GND”. See below
figure.

Figure 22 – JP1 VBAT connector

3.6 VADJ selection - JP5

VADJ rail is configurable via JP5. VADJ is an independent rail supplying power to the Zynq PL
I/O banks and connected Pmods. VADJ drives banks 34 and 35

.

WARNING: When using a 7030 SOM, VADJ MUST remain at the
1.8V setting otherwise the SOM will be damaged!

Use the table below for Vadj selection.

NOTE: if JP5 is left open, the board defaults to +1.8V VADJ rail setting.

JP5 Jumper Position (pins)

VADJ

1-2 or Open

1.8V

3-4

2.5V

5-6

3.3V

Table 20 – VADJ Selection Table JP5

«
...
32
33
34
35
36
...
»

Содержание PicoZed FMC V2











































Отзывы:

Нет отзывов

Похожие инструкции для PicoZed FMC V2

Fatal1ty Z170 Gaming K4 Series

Бренд: ASROCK Страницы: 163

Бренд: ECS Страницы: 27

Бренд: Advantech Страницы: 3

Бренд: Biostar Страницы: 43

Freescale MC9S08MM128

Бренд: NXP Semiconductors Страницы: 12

975X Platinum Series

Бренд: MSI Страницы: 157

Бренд: Abit Страницы: 72

Бренд: IEI Technology Страницы: 11

GF7100P-M7 - BIOS SETUP

Бренд: Biostar Страницы: 45

Бренд: Gigabyte Страницы: 38

Бренд: Texas Instruments Страницы: 23

Бренд: Texas Instruments Страницы: 33

Бренд: JETWAY Страницы: 50

Бренд: Linear Technology Страницы: 8

Бренд: DFI Страницы: 26

Fatal1ty Z77 Professional-M

Бренд: ASROCK Страницы: 245

Бренд: Gigabyte Страницы: 2

Бренд: Selva Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды