AvL Technologies AAQ Step Track Hold Module Скачать руководство пользователя страница 13

Страница: 13 / 15

Step Track Hold Tracking

AvL Technologies

| Proprietary – Content is Subject to Change without Notice

4.2.

Sensor Outputs

Path

Main Window → View→ Sensor Output
Level 0

Figure 6 - Sensor Outputs

Item

Level

Description

Current Signal Average

The average of the current signal

Current Signal Gradient

The rate of change of the current signal level

Current Signal Latched

Lock

Reports if modem ever locked.

Current Signal Level

The Signal to Noise ratio that is being reported by the modem in use.

This is the signal that the controller will use to peak on.

Current Signal Lock

If the signal is above the configured threshold

Current Signal Noise

The amount of noise in the current signal level.

Current Signal Source

The type of signal source being used to scan

Current Signal Type

The type of signal being picked up by scanning

Step Track Hold

Elevation Inc Average

Based on the Configuration item, “Elevation Inclinometer Counts”. This

is the Inclinometer averaged reading.

Step Track Hold Pedestal

Elevation Target

After a peaking cycle is complete, the pedestal Elevation axis is latched

for current cycle. This value is read here.

Step Track Hold Target
Elevation Inclinometer

Following peaking cycle, the actual inclinometer is read here.

Содержание AAQ Step Track Hold Module
















Результаты поиска

Содержание AAQ Step Track Hold Module

Отзывы:

Похожие инструкции для AAQ Step Track Hold Module

Бренды по названию

Популярные бренды

AvL Technologies AAQ Step Track Hold Module, Руководство по установке и эксплуатации

Результаты поиска

Содержание AAQ Step Track Hold Module

Отзывы:

Похожие инструкции для AAQ Step Track Hold Module

Бренды по названию

Популярные бренды