AvL Technologies AAQ Step Track Hold Module Скачать руководство пользователя страница 4

Страница: 4 / 15

Step Track Hold Tracking

AvL Technologies

| Proprietary – Content is Subject to Change without Notice

Setup Guide

2.1.

Hardware

No additional hardware is required for the operation of this module.

2.2.

Software

Verify that you are using the correct revision software.

Version Info

Main Window → Help → Version
Level 0

Be sure that the Remote Client, ROM, and device module are at or above the versions shown below:

Figure 1 - Version Information

2.3.

Hardware Connection

2.3.1.

Serial Communication Connection

Serial connection is not an option for the hardware associated with this module.

2.3.1

Ethernet Communication Connection

The Ethernet connection is internal for this module and reconfiguration is not an option.

Содержание AAQ Step Track Hold Module
















Результаты поиска

Содержание AAQ Step Track Hold Module

Отзывы:

Похожие инструкции для AAQ Step Track Hold Module

Бренды по названию

Популярные бренды

AvL Technologies AAQ Step Track Hold Module, Руководство по установке и эксплуатации

Результаты поиска

Содержание AAQ Step Track Hold Module

Отзывы:

Похожие инструкции для AAQ Step Track Hold Module

Бренды по названию

Популярные бренды