Avital 2100 Скачать руководство пользователя страница 9

Страница: 9 / 26

This security system can control Type A door locks directly, with no additional parts. The switch will have three

wires on it, and one will test (+)12V constantly. The others will alternately pulse (+)12V when the switch is

pressed to the lock or unlock position.

If you cannot get to the switch, and you find a set of wires that pulse (+)12V alternately on lock and unlock,

you must take care to ensure that it is not a Type C direct-wire system.

IMPORTANT!

If you mistake a Type C direct-wired system for a Type A positive-pulse system, the

module will be damaged!

Here is a test: Cut the wire which pulses (+)12V on lock, and then operate the switch to unlock.

■

If all doors unlock, the vehicle uses a Type A system.

■

If you lose all door lock operation in both directions, you are operating the master switch in a Type C system.

■

If one or more, but not all, motors stop operating, you have cut a wire leading directly to one or more motors.

Reconnect the wire and look for another wire.

Many domestically-made GM vehicles use Type A locks. However, many more GM vehicles are Type C than in pre-

vious years. The full-size pickups (1989-later), many of the S10 Blazers, the Corvette, '95 Cavalier/Sunfire 1993

and newer, Camaro/Firebird all use Type C door locks, and cannot be controlled without a 451M! Almost all domes-

tically-built Fords are Type C. Ford builds almost no Type A systems. Chrysler builds both Type A and Type C, so

test carefully.

IMPORTANT!

Remember that the functions of these wires reverse between Type A and Type B!

type A: positive (+) 12V pulses from the switch to the factory relays

Содержание 2100



























Результаты поиска

Содержание 2100

Отзывы:

Похожие инструкции для 2100

Бренды по названию

Популярные бренды

Avital 2100, Руководство по установке

Результаты поиска

Содержание 2100

Отзывы:

Похожие инструкции для 2100

Бренды по названию

Популярные бренды