Avital 2100 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 26

background image

8

© 2001 Directed Electronics, Inc. Vista, CA

Before connecting this wire, remove the supplied fuse. Connect to the positive battery terminal or the constant

12V supply to the ignition switch.

NOTE:

Always use a fuse within 12 inches of the point you obtain (+)12V power. Do not use the

15A fuse in the harness for this purpose. This fuse protects the module itself.

When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the red/white wire will

supply an output as long as the transmission continues. This is often used to operate a trunk/hatch release or

other relay-driven function.

IMPORTANT!

Never use this wire to drive anything but a relay or a low-current input! The transis-

torized output can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other
high-current device will cause it to fail.

door lock harness (H2) wire connection guide

______

______

______

This security system can control two common power door lock types without any additional parts! With

certain vehicles, or if an actuator is to be installed, either a

451M

Door Lock Relay Satellite or two relays will

be required.

BLUE

(+) LOCK, (-) UNLOCK OUTPUT

OPEN

UNLESS USING 451M

GREEN

(-) LOCK, (+) UNLOCK OUTPUT

H2/1

H2/2

H2/3

H1/12 RED/WHITE channel 2, (-) 200mA output

H1/11 RED (+)12V constant power input

«
...
6
7
8
9
10
...
»

Содержание 2100



























Отзывы:

Нет отзывов

Похожие инструкции для 2100

Бренд: Garmin Страницы: 6

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренд: Autopage Страницы: 20

Бренд: BRK electronic Страницы: 30

Бренд: Geemarc Страницы: 11

Бренд: Apollo Страницы: 2

Exactime DRC-604

Бренд: Datexx Страницы: 4

Бренд: IKEA Страницы: 8

Бренд: Masterbuilt Страницы: 36

Бренд: Anka Страницы: 8

Бренд: Sharper Image Страницы: 4

Бренд: Sharper Image Страницы: 6

Бренд: Ambient Weather Страницы: 10

Бренд: Clarion Страницы: 15

Бренд: Clarion Страницы: 16

Бренд: Clarion Страницы: 38

Бренд: Dicon Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды