Avital 2100 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 26

background image

© 2001 Directed Electronics, Inc. Vista, CA

5

(-) Negative Light Flash Output

NOTE:

For parking light circuits that draw 10 amps or more, the internal jumper must be switched

to a (-) light flash output. (See the Internal Programming Jumper section of this guide.)

P/N 8617

or a standard automotive SPDT relay must be used on the H1/2 light flash output harness wire.

This wire provides a (-) 200 mA output whenever the transmitter code controlling Channel 3 is received. This

output will continue as long as that transmission is received. Use for options such as

551T

Valet® Start system,

529

T or

530T

power window controllers, etc.

IMPORTANT!

Never use this wire to drive anything except a relay or a low-current input! The tran-

sistorized output can only provide 200 mA of current, and connecting directly to a solenoid, motor,
or other high-current device will cause it to fail.

Connect the H1/4 BLACK/WHITE wire to an optional relay for interior light illumination (

p/n 8617

or standard

automotive SPDT relay).

IMPORTANT!

This output is only intended to drive a relay. It cannot be connected directly to

the domelight circuit, as the output is not able to support the current draw of one or more
light bulbs.

H1/4 BLACK/WHITE (-) interior light illumination output

H1/3 WHITE/BLUE (-) channel 3 output

«
...
3
4
5
6
7
...
»

Содержание 2100



























Отзывы:

Нет отзывов

Похожие инструкции для 2100

Бренд: Extech Instruments Страницы: 7

Бренд: La Crosse Technology Страницы: 8

Бренд: Bellman & Symfon Страницы: 4

Бренд: Emerald Страницы: 4

Бренд: Uniden Страницы: 12

Бренд: Viper Страницы: 45

Бренд: General Monitors Страницы: 72

Бренд: Audiovox Страницы: 38

Бренд: Trevi Страницы: 8

Prestige APS-2K4

Бренд: Audiovox Страницы: 6

Бренд: philippi Страницы: 6

Бренд: Quantys Страницы: 41

CoolStart RS-1604TW1

Бренд: CrimeStopper Страницы: 28

SD-218-A Series

Бренд: Sentek Страницы: 4

Бренд: Hyundai Страницы: 20

Бренд: Voxx Страницы: 16

Бренд: Oregon Scientific Страницы: 23

Бренд: VARO Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды