Avital 2100 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 26

background image

14

© 2001 Directed Electronics, Inc. Vista, CA

This system usually requires a negative pulse to unlock, and cutting the wire to lock the door. In some vehicles,

these are reversed. It is found in late-model Nissan Sentras, some Nissan 240SX, and Nissan 300ZX 1992 and later.

It is also found in some Mazda MPV's and some Mitsubishi's.

One relay (optional) is used to interface to this type of system as follows:

type F: one-wire system

«
...
12
13
14
15
16
...
»

Содержание 2100



























Отзывы:

Нет отзывов

Похожие инструкции для 2100

Бренд: Hama Страницы: 2

Бренд: Ultra Start Страницы: 16

Бренд: La Crosse Technology Страницы: 8

Smoky Mountain Great Outdoors 3625BGD

Бренд: Landmann Страницы: 29

Бренд: Smartwares Страницы: 2

TRUSENSE SMOKE 2050-DS10

Бренд: Kidde Страницы: 28

Бренд: NATURE & DECOUVERTES Страницы: 17

Бренд: CrimeStopper Страницы: 1

Бренд: CrimeStopper Страницы: 7

Бренд: Fire-Lite Страницы: 1

Бренд: CrimeStopper Страницы: 18

CS-2000DPII TW2

Бренд: CrimeStopper Страницы: 24

CoolStart RS1905FM

Бренд: CrimeStopper Страницы: 32

Бренд: CrimeStopper Страницы: 4

Бренд: Defender Страницы: 5

Бренд: Avital Страницы: 28

Бренд: La Crosse Technology Страницы: 9

Бренд: OnLyee Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды