manualshive.com logo in svg

Avidyne 700-00004 Series, Руководство по установке, Страница: 55 / 132

Поделиться
Скачать
Avidyne 700-00004 Series Скачать руководство пользователя страница 55

 

EX5000 Installation Manual

 

P/N 600-00073 Rev 24

- 45 -

 Lightning Sensor Noise Mode

When operating the Lightning sensor (WX-500 only) in Noise Monitor mode, the Lightning button on 
the Map page will display “Noise” as the current Lightning state. 

➥

Do not press the button in this state, or it may suppress lightning display unnecessarily. 

See the operating guide for the Lightning Sensor for more information.

If no lightning strikes are shown at all during noise testing, press the button until it says Display Off, 
then press once more to return to the proper Noise mode display.

Lightning Sensor is Not Communicating

Communication between the Lightning sensor to the MFD has been 
lost. The wiring may be incorrect, the MFD setup may not match the 
wiring or the sensor may have an error.

Lightning Ahead

The Lightning Ahead option has been checked on the Lightning 
Setup page. Displayed when a Lightning Ahead condition exists.

Lightning Heading Source Failed

Heading data is no longer available from the WX-500. Strike data 
may still be valid. Will only appear if the WX-500 is used as the 
heading source.

Lightning Heading Source OK

Heading data has been restored.

Stuck mic-PLEASE CHECK

Check your COM transmitters for indication of a stuck mike.

Lightning Antenna Location Changed

There may be an inconsistency between the antenna location 
jumper setting and the software configuration. This message should 
only appear during installation.

Lightning Position Source Failed 

(TWX-670 

only)

The position reporting source (GPS or FMS) connected to the 
TWX-670 has encountered a fatal fault.

Lightning Position Source OK 

(TWX-670 only)

The position reporting source (GPS or FMS) connected to the 
TWX-670 has returned to normal operation.

Noise Present 

(TWX-670 only)

The TWX-670 has detected excessive noise in the system.  
Accuracy and efficiency of the lightning sensor may be 
negatively affected.

Stuck MK 

(TWX-670 only)

Microphone PTT switch is stuck open.  Lightning strikes will  
not be displayed until the problem is fixed.

No Position Data 

(TWX-670 only)

The position reporting source (GPS or FMS) connected to the 
TWX-670 is not sending position data.

Table 19:  Lightning Sensor Messages (Continued)

Message

Meaning

Содержание 700-00004 Series





































































































































Отзывы:

Нет отзывов