Avid Technology VENUE SC48, Руководство пользователя, Страница: 129 / 272

Chapter 15: Solo and Monitor Busses 117
Activating Phantom Power for Talkback Input
The Talkback input on the back panel has ava15V
phantom power for using a condenser microphone.
To apply phantom power to the talkback mic input:
„
On the back panel, move the Talkback Mic Phantom Power
switch to the right.
Using 2-Track Inputs and Outputs
Analog and Digital 2-Track Inputs and Outputs are available
on the back panel of the console.
Assigning 2-Track Source Input
To assign the 2-Track inputs to Input Channels or FX Returns:
1
Go to the
Patchbay > Inputs
tab and click the
Channels
tab or
the FX Returns tab.
2
At the top of the channel grid, click the
FOH
tab.
3
Click in the channel grid to assign any of the following
2-Track input sources (listed at the top right of the grid) to an
Input Channel or FX Return (listed on the left):
• AL (Analog Left)
• AR (Analog Right)
• DL (Digital Left)
• DR (Digital Right)
Activating 2-Track Input and Setting Level
To feed 2-Track input to the Monitor and Mains busses:
1
Go to the
Options > Misc
screen.
2
In the 2-Track section, click the
Input Fed to Monitors and
Masters
pop-up and select
Analog 2-Track
or
Digital 2-Track
.
To activate 2-Track input and set level:
1
Click the on-screen
In
button in the
2-Track
section of the
Op-
tions > Misc
page.
2
Drag the on-screen
Level
knob in the
2-Track
section of the
Options > Misc
page.
Routing 2-Track to an Output Bus
To route the 2-Track inputs directly to an output bus:
1
Go to the
Options > Misc
tab.
2
Click the
Route
button in the
2-Track
section on-screen. The
switch flashes to indicate
Route to Selected
mode.
3
Press the Select switch on each of the output channels
(Auxes, Groups, Matrixes, or Mains) where you want to route
2-Track signal. The Select switches flash to indicate 2-Track as-
signment.
4
Click
Done
in the
Route to Selected
dialog to confirm the as-
signment.
Routing to the 2-Track Outputs
You can route any output bus or Direct Output to the 2-Track
outputs.
To route any output bus to the 2-Track outputs:
1
Go to the Patchbay and click the Outputs tab.
2
To the left of the channel grid, click the tab for an Output
bus ( Auxes, Groups, PQs, Matrixes , or Mains ).
3
At the top of the channel grid, click the FOH tab.
4
Click in the channel grid to assign an Output bus (listed on
the left) to any of the following 2-Track output sources (listed
at the top right of the grid):
• AL (Analog Left)
• AR (Analog Right)
• DL (Digital Left)
• DR (Digital Right)
To route a Direct Output to the 2-Track outputs:
1
Go to the Patchbay and click the
Directs
tab.
2
To the left of the channel grid, click the tab for a channel
source (Channels, FX Returns, or Outputs).
3
At the top of the channel grid, click the
FOH
tab.
4
Click in the channel grid to assign a channel source (listed
on the left) to any of the following 2-Track output sources
(listed at the top right of the grid):
• AL (Analog Left)
• AR (Analog Right)
• DL (Digital Left)
• DR (Digital Right)
2-Track controls in the Options > Misc page
Signals are routed to output busses post-mute and post
fader.
courtesy of
www.sxsevents.co.uk
Phone: 0870 080 2342
email: enquiries@sxsevents.co.uk
Event production and Audio-Visual Services
www.sxsevents.co.uk