manualshive.com logo in svg

Avery Weigh-Tronix 7820-50, Инструкция пользователя

Поделиться
Скачать
Avery Weigh-Tronix 7820-50 Скачать руководство пользователя страница 26

 26

7800 Family User Instructions

AUTO-2:

Weight is automatically transmitted when the item is placed on the scale and the weight 
stabilizes. This option is normally used in an application where the item placed on the 
scale is sealed and ready for the shipment weight to be registered. The minimum stable 
weight required to trigger an auto SEND is set at five display divisions (i.e. 5d).

PRINT: 

Weight is transmitted only when the 

TEST

 button on the display panel is pressed. The 

TEST

 button is redefined as a SEND key when in the normal weight mode only. 

See 

Note 2 below.

 On some specially modified units, the serial port connector or an 

additional internal connection to the display 

TEST

 button can also be used for a remote 

push button to initiate the manual send sequence.

NOTES:

1.

The output print formats for AUTO-1, AUTO-2 and manual print operation are 
defined in 

Table 5.3

 and set in the PRTOUT setting of the CONF menu. 

2.

The 

TEST

 button will retain its test function (i.e. will not be redefined as a 

SEND key) when displayed weight is at zero as indicated when the Center-
Zero indicator is on. 

3.

While in AUTO-1, AUTO-2, or manual print modes, scale will not respond to 
external serial commands.

5.9 Calibration Mode

The Calibration (CAL) Mode menu lets you calibrate your scale. The items in the 
calibration menu are as follows:

POUNDS/KILOGRAMS (LBS or 1000 Gr)

 – Selects the unit of measure of your 

calibration test weights (lb or kg).

SCALE or CLASS

 – Selectable only when calibrated in LBS (lb) mode. Selection of 

SCALE

 rounds weight at 0.5 divisions. Selection of 

CLASS

 sets device up as a weight 

classifier rounding at 0.9 divisions.

5.9.1 Step-by-Step Instructions for CAL Mode

CAPACITY (100.02, 150.05, 250.05, 300.1, etc.)

 – Select the capacity of the scale.

Follow these steps to calibrate the scale. Refer to the 

Menu on page 17

.

1.

From the 

DIAG

 display, press the 

ZERO

 key until 

CAL

 is displayed, or from the 

normal weighing mode, move Switch 1 to the Menu mode or OPEN position. 
Press the 

ZERO

 key until 

CAL

 is displayed. 

2.

Press the 

TEST

 key …

LBS

 (lb) or 

1000G

 (kg) is displayed.

Содержание 7820-50









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды