background image

11 Disposal

O

Comply with national regulations regarding disposal.

12 Troubleshooting

Table 13 contains an overview of malfunctions, possible causes, and remedies.

13 Technical Data

If you cannot remedy a malfunction, please contact AVENTICS GmbH. The 
address is printed on the back cover of these instructions.

Table 13:

Table of malfunctions

Malfunction

Possible cause

Remedy

No output pressure 
present

No power supply

Connect the power sup-
ply.

Check the polarity of the 
power supply.

Switch on system com-
ponent.

No set point stipulated

Stipulate a set point.

No operating pressure

Connect the operating 
pressure.

Output pressure too low 
(less than the set point)

Operating pressure too low

Increase the operating 
pressure.

A consumer with a high air 
consumption is located in 
the EV1X operating line and 
results in a large pressure 
drop in the device.

Reduce air consumption.

Operating pressure less 
than 1 bar above the 
maximum output pressure 
to be controlled.

Adjust the operating 
pressure to at least 1 bar 
above the maximum 
output pressure to be 
controlled.

Air is audibly escaping

Seal is missing or damaged

Check the seals and re-
place, if necessary.

Pressure regulator is not 
leaktight

Exchange the pressure 
regulator

Pressure regulator 
emits short pressure 
pulses

Device with current input is 
operated with voltage set 
point

Stipulate the correct type 
of set point

Outlet pressure jumps 
to the level of the oper-
ating pressure

Set point too high
(> 20 mA  or  > 10 V)

Stipulate the correct set 
point

Output pressure too 
high

Dynamic pressure in ex-
haust

Check the exhaust line

DIAG LED illuminated 
red

Parameter error

Stipulate valid parame-
terization

Safety cut-off active

Exchange device since a 
pressure sensor is defec-
tive.

Table 14:

General data

General data

Dimensions 
(width x height x depth)

EV12: 63 mm x 160 mm x 138.5 mm
EV18: 85 mm x 180 mm x 167 mm

Weight

EV12: 1.4 kg
EV18: 2.15 kg

Operating temperature 
range

0

°

C to 50

°

C

Storage temperature 
range

-25

°

C to 80

°

C

Ambient operating condi-
tions

Max. height above sea level: 2000 m

Version

Externally piloted pressure regulator

Permissible medium

Compressed air

Pneumatic connections

EV12: G1/2 and G3/8
EV18: G1 and G3/4

Max. particle size

50 μm

Oil content of compressed 
air

0-5 mg/m

3

The pressure dew point must be at least 15°C below the ambient and medium 
temperatures and must not exceed 3°C.
The oil content of compressed air must remain constant during the life cycle.

O

Use only the approved oils from AVENTICS, see the AVENTICS online catalog, 
chapter “Technical information”.

Mounting orientation

Any if used with dry and oil-free compressed air

Protection class according 
to EN 60529/IEC60529

IP65 (only when assembled and with all plugs 
connected)

Relative humidity

95%, non condensing

Degree of contamination

2

Use

Only in closed rooms

Table 15:

Pneumatic data EV12 pressure regulator

Pneumatics

Flow rate values of the EV12 pressure regulator

Supply 

pressure [bar]

Set pressure 

[bar]

Output 

pressure [bar]

Q [l/min] 

Type L/R

Type C

11

10

9.8

3500

3500

11

10

9.0

4600

4600

7

6

5.8

2800

2800

7

6

5.0

3700

3550

Flow characteristic curves of EV12 pressure regulators type L and type R

Flow characteristic curves of EV12 pressure regulators type C

Table 16:

Pneumatic data EV18 pressure regulator

Pneumatics

Flow rate values of the EV18 pressure regulator

Supply pressure 

[bar]

Set pressure [bar]

Output pressure 

[bar]

Q [l/min] 

Type L/R

10

8

8.8

9000

10

6

5.8

11000

10

4

3.8

15000

Flow characteristic curve of EV18 pressure regulator

Table 14:

General data

General data

[psi]

[bar]

10

8
7
6
5
4
3
2
1
0

0

1000

2000

3000

4000

5000

6000

7000

8000

[Nl/min]

9

145

116

101,5

87

72,5

58

43,5

29

14,5

0

130,5

P  = 3 bar

v

P  = 5 bar

v

P  = 7 bar

v

P  = 9 bar

v

P  = 11 bar

v

 P

a

 =

 outpu

p

ressure

P

v

 = supply pressure (= output pr 1 bar)

[psi]

[bar]

10

8
7
6
5
4
3
2
1
0

9

145

116

101,5

87

72,5

58

43,5

29

14,5

0

130,5

0

1000

2000

3000

4000

5000

6000

7000

8000

[Nl/min]

P  = 3 bar

v

P  = 5 bar

v

P  = 7 bar

v

P  = 9 bar

v

P  = 11 bar

v

 P

a

 =

 outp

ut pressure

P

v

 = supply pressure (= output pr 1 bar)

[psi]

[bar]

10

8
7
6
5
4
3
2
1
0

9

145

116

101,5

87

72,5

58

43,5

29

14,5

0

130,5

0

3000

6000

9000

12000

15000

18000

[Nl/min]

P

a

 =

 outp

ut pressure

P

v

 = supply pressure = 10 bar

AVENTICS

 | EV12/EV18 | R414011404–BAL–001–AA | English

21

Содержание EV12





































































Отзывы: