manualshive.com logo in svg

Avaya Virtual Services Platform 7200 Series, Руководство по установке

Поделиться
Скачать
Avaya Virtual Services Platform 7200 Series Скачать руководство пользователя страница 25

Installing slides in a 600mm-900mm equipment rack

Use the following procedure to install your switch in an equipment rack with a depth between
600mm and 900mm.

Procedure

1. Disconnect the power cord from the switch.

2. Detach the chassis rail from the slide’s rack rail. (See Step 2 of 

Installing slides in a

300mm-600mm equipment rack

.)

3. Lift the locking mechanism on the rack rail to slide the outer section back into the main

section. (See Step 3 of the 300mm-600mm instructions.)

4. Attach the chassis rail to the chassis. (See Step 4 of the 300mm-600mm instructions.)

5. Remove the two screws and nuts securing the short rear bracket to the rack rail. This

bracket is for 300mm-600mm equipment racks only and is not used in this installation. Save
the bracket for possible future use.

January 2015

Installation Job Aid for Avaya Virtual Services Platform 7200 Series     

25

Содержание Virtual Services Platform 7200 Series


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды