manualshive.com logo in svg

Avaya Virtual Services Platform 7200 Series, Руководство по установке

Поделиться
Скачать
Avaya Virtual Services Platform 7200 Series Скачать руководство пользователя страница 16

Installing the VSP 7200 in an equipment

rack

Note:

The instructions in this section apply to all switches in the Avaya Virtual Services Platform 7200
Series and Avaya Virtual Services Platform 8000 Series. The illustrations show the VSP 8200
as an example, but the instructions apply to any switch in these series.

There are two ways to install the VSP 7200 in an equipment rack. Refer to one of the following
sections:

• Slide Rack Mount Kit-This is a separately ordered option that you can use to install your switch

in equipment racks that range from 300mm to 900mm deep. For installation instructions, see 

Using the optional slide rack mount kit

.

• Brackets-The switch comes with brackets that you can install on the chassis. For installation

instructions, see 

Using the supplied brackets

.

Before you begin

• Ensure that there is enough rack space to accommodate a 2RU switch (8.8 cm).
• The rack is bolted to the floor and braced if necessary.
• The rack is grounded to the same grounding electrode used by the power service in the area.

The ground path must be permanent and must not exceed 1 Ohm of resistance from the rack

to the grounding electrode.

About this task

Caution:

When you mount the device in a rack, do not stack units directly on top of one another. You

must secure each unit to the rack with the appropriate mounting brackets. Mounting brackets

cannot support multiple units.

Using the optional slide rack mount kit

The Universal Slide Rack Mount Kit is adjustable so that you can install your switch in equipment
racks of different sizes. Use the following procedures to install your switch in equipment racks with a
depth from 300mm to 900mm.

This kit is a separately ordered item (Part # EC8011002).

For instructions see:

•

Installing slides in a 300mm-600mm equipment rack

•

Installing slides in a 600mm-900mm equipment rack

•

Important notice about rack safety

•

Removing the switch from an equipment rack

January 2015

Installation Job Aid for Avaya Virtual Services Platform 7200 Series     

16

Содержание Virtual Services Platform 7200 Series


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды