AV-GAD AVG064 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 12

AV-GAD AVG064 Скачать руководство пользователя страница 2

2

AVG064 Description

The AVG064 is a compact Dual Band GSM gate control. The unit is designed for cellular
access control housed in an ABS case with a separated power supply.
The  AVG064  contains  a  built-in  relay,  which  is  remote  controlled  and  is  applicable  for
access control for parking lots, home automation, garage barriers, etc.
The factory default is for European GSM band: 900/1800 MHz.
AVG064  standard  pack  contains:  GSM  unit,  Zero  dB  GSM  antenna,  Installation  Manual,
four  wires  Cable,  three  wires  cable  for  power  and  outputs.  Power  supply  is  not  included.
For power supply the AV-20 wall plug type, or the AV-21 are compatible, both 12V 1A DC.

The AVG064 support up to 64 accounts for gate or door opening, or use the “Open to all
feature” (#ACM command).

Programming and parameter settings are executed by SMS commands, PC connection is not
available.

AVG064 Wiring

1. Connections:

Gently insert SIM card to

SIM

slot, located at the bottom side, as shown in figure 1.

Connect GSM antenna to

ANT

connector.

2. Plug the Power Supply as shown in figure 1.

Figure 1: AVG064 power and relay wiring

SIM card parameters:

Make sure the SIM you are using is SMS enabled, without a voice

message service, without charge limits, caller ID is enabled, unlocked, PIN code disabled.

Install the AVG064 GSM Remote Control Device in a place where there is GSM signal is well
received from the operator you want to use. Check it with a phone before proceeding with
the installation. To install the device in a place with a weak signal, consider using an external
antenna (option to be purchased separately with a 5m cable).

«
1
2
3
4
...
»

Содержание AVG064













Отзывы:

Нет отзывов