Autoquip PLTC-58120 Скачать руководство пользователя | Manualshive

Страница: 21 / 56

background image

21

4.4

Surface Installation

Surface installation procedures are the same as for pit installation instructions with the following
consideration:

The surface area where the lift will be set must be flat and level
and be of sound concrete of sufficient thickness to support the

lift while loaded at full capacity. Asphalt is not sufficient support for the
lift.

22.

4.5

Shimming And Anchoring Lift To Concrete

Recommended concrete anchor bolts are: HILTI “Kwik-Bolt”, Molly Parabolt or similar.

1. Verify lift is positioned correctly.

2. Raise the platform and install the maintenance leg (see

“Maintenance Device Instructions” section).

3. Drill holes in concrete as specified by anchor bolt

manufacturer.

4. Install and tighten anchors as specified by anchor bolt

manufacturer.

5. Each lag bolts should be able to withstand 2000lbs.

minimum upward pull.

6. After lift has been aligned, leveled and shimmed, and

anchors have been installed, pour grout under entire
base frame.

7. When grout has set and cured, tighten nuts on anchor bolts.

8. Route hydraulic hose or electrical cord through conduit in pit wall.

NOTICE

«
...
19
20
21
22
23
...
»

Содержание PLTC-58120

























































Отзывы:

Нет отзывов

Похожие инструкции для PLTC-58120

Бренд: POP UP Страницы: 20

Бренд: Snorkel Страницы: 20

Бренд: Workplace Products Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды