AUTHOR Alarm IGLA Скачать руководство пользователя страница 9

Страница: 9 / 48

FIRMWARE UPDATE

The IGLA ALARM system firmware update is

implemented remotely through the Bluetooth channel

with no need to dismount the device.

In order to update the firmware, you will need to:

1. Download and install the BLE112-module driver (the

USB-dongle should be connected to the computer).

2. Download the archive with the

Author Flasher

software and unpack it to any folder on the

computer.

Transfer the IGLA ALARM to the firmware change

mode and perform the updating procedure using the

Author Flasher

tool.

BLED 112 drivers installation

1. Unpack the «Driver BLE adapter.7z»-archive content

to any folder on the computer.

2. Connect the USB-dongle to the computer.

3. Open the device manager on the computer (works

only Windows-operated computers):

Start – Control panel – Device manager

or click the right button of the mouse on the icon

This computer – Operation – Device manager.

4. Find the new device in the list of the new devices.

It may be ticked with the exclamation sign «!» as

unidentified device and may be placed into:

• Ports (COM and LPT)

• USB-controllers

• Other devices

Содержание IGLA

















































Результаты поиска

Содержание IGLA

Отзывы:

Похожие инструкции для IGLA

Бренды по названию

Популярные бренды

AUTHOR Alarm IGLA, Руководство по обслуживанию

Результаты поиска

Содержание IGLA

Отзывы:

Похожие инструкции для IGLA

Бренды по названию

Популярные бренды