AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 36

AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 6

Hardware Installation Manual

6

Document #: LTRT-41503

Mediant 4000 E-SBC

Related Documentation

Manual Name

SIP Release Notes

Mediant 4000 E-SBC User's Manual

Notes and Warnings

Warning:

The device is an

indoor

unit and therefore, must be installed ONLY

indoors.

Warning:

Installation of this device must be in a weather protected location of

maximum ambient temperature of 40°C.

Warning:

Installation and service of this device must be made only by qualified

service personnel in restricted access locations and connected to an
earthed power socket.

Caution Electrical Shock

Do not attempt to open or disassemble this device. The device carries high
voltage. Contact with internal components may cause electrical shock and bodily
harm.

Warning:

This device is intended to accommodate only AMC modules approved by

AudioCodes.

Warning:

Modules may contain a non-rechargeable lithium battery. If you need to

replace the battery, replace it only with batteries of the same type and
manufacturer.

Documentation Feedback

AudioCodes continually strives to produce high quality documentation. If you have any
comments (suggestions or errors) regarding this document, please fill out the
Documentation Feedback form on our Web site at

http://www.audiocodes.com/downloads

«
...
4
5
6
7
8
...
»

Содержание Mediant 4000 E-SBC





































Отзывы:

Нет отзывов