AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 15

Version 6.6

15

September 2013

Hardware Installation Manual

3. Physical Description

Table

3-5: E-SBC Module LEDs Description

Item #

LED

Color

State

Description

1

Green

On

Module in service

-

Off

Module out of service

2

-

Off

During booting up state

Red

On

Booting up phase / fault detected in module

Green

On

Normal operation

3

-

Off

During booting up state

Green

On

Application running in Standalone state

Flashing

Application running in High Availability (HA)
Active state

Yellow

On

Application is starting Boot / synchronizing
HA

Flashing

Application is running in HA Redundant state

4

Red

On

Out of service

-

Off

Normal operation

5

Left LED

on

Ethernet

Ports

Green

On

Ethernet link established.

Flashing

Data is being received or transmitted
(activity) on the Ethernet port.

-

Off

No Ethernet link.

6

Right LED

on

Ethernet

Ports

Orange

On

1000Base-T (Gigabit) Ethernet link
established.

-

Off

No Ethernet link or 100Base-Tx link
established.

7

Blue

On

Blue hot-swap LED indicating that the AMC
module can be fully removed or inserted.

Note:

Do not remove the module before this

LED turns blue.

-

Off

The module insertion process is complete.

«
...
13
14
15
16
17
...
»

Содержание Mediant 4000 E-SBC





































Отзывы:

Нет отзывов