AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 36

AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 30

Hardware Installation Manual

30

Document #: LTRT-41503

Mediant 4000 E-SBC

5.4

Connecting to Power

The procedure below describes how to connect the device to the power supply.

Warnings:

•

The device must be connected (by service personnel) to a socket-outlet with
a protective earthing connection.

•

Use only the AC power cord supplied with the device.

Notes:

•

You can connect both Power Supply modules (1 and 2), for 1+1 power load-
sharing and redundancy. Each module provides an AC power socket on the
device's rear panel. If both power modules are used, ensure that you
connect each one to a different AC supply socket.

•

The two AC power sources must have the same ground potential.



To connect the device to the power supply:

1.

Connect the AC power cord (supplied) to one of the power sockets located on the rear
panel.

Figure

5-8: Connecting to Power

2.

Connect the other end of the power cord to a standard AC electrical outlet (100-
240V~50-60 Hz).

3.

For load sharing and power redundancy, repeat steps 1 through 2, but using the
power socket of the second Power Supply module and connecting this to a different
supply circuit.

4.

Turn on the power at the power source (if required).

5.

Check that the

POWER

LED on each Power Supply module (front panel) is lit green.

This indicates that the device is receiving power.

«
...
28
29
30
31
32
...
»

Содержание Mediant 4000 E-SBC





































Отзывы:

Нет отзывов