AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

AudioCodes Mediant 4000 E-SBC Скачать руководство пользователя страница 11

Version 6.6

11

September 2013

Hardware Installation Manual

3. Physical Description

3

Physical Description

This section provides a physical description of the device.

3.1

Physical Dimensions

The device's physical dimensions are listed in the table below.

Table

3-1: Physical Dimensions

Item

Description

Enclosure

4/8-slot, 1U chassis

Dimensions (H x W x D)

1U x 19” (444 mm) x 14” (355 mm)

Weight

Approx. 11.7 lbs (5.3 kg)

Environmental



Operational: 0 to 40°C (32 to 104°F)



Storage: -20 to 70°C (-4 to 158°F)



Relative Humidity: 10 to 85% non-condensing

3.2

Front Panel Description

The device's front panel is shown in the figure below and described in the subsequent
table.

Figure

3-1: Front Panel

Note:

The figure above provides only an example of the Mediant 4000 hardware
configuration; module slot locations and type of modules (e.g., Media Processing
Module) depend on the ordered hardware configuration.

«
...
9
10
11
12
13
...
»

Содержание Mediant 4000 E-SBC





































Отзывы:

Нет отзывов