AuCom MVS0080 Скачать руководство пользователя | Manualshive

Страница: 24 / 53

background image

INSTALLATION: SETUP TOOLS

MVS Series

23

710-03261-00D

Setup Tools

7

MVS soft starters offer programming and simulation features specifically designed
to make commissioning safe and easy.

7.1 Simulation

Tools

Software simulation functions allow the MVS to be tested without a motor
connected, to confirm that the soft starter's control circuits are operating correctly.
There are three simulation modes available:

•

Run simulation: simulates a motor starting, running and stopping to confirm
that the soft starter has been installed correctly.

•

Protection simulation: simulates activation of each protection mechanism to
confirm that the soft starter is responding correctly in each situation.

•

Signalling simulation: simulates output signalling to confirm that outputs are
operating correctly.

For details of the simulation functions, refer to

Commissioning Menu: Simulation

Tools

on page 30.

7.2

Low Voltage Test Mode

The MVS can be connected to a low voltage motor (

≤

500 VAC) for testing. This

allows the user to thoroughly test the soft starter and its associated power and
control circuits. The low voltage test mode provides a means of testing the soft
starter's configuration without requiring a full medium voltage test facility. To
perform the low voltage test, one non-conduction resistor assembly must be
connected to each phase arm (three resistor assemblies are supplied with the soft
starter).

During the low voltage test, the soft starter's input, output and protection settings
can be tested. Low voltage mode is not suitable for testing soft starting or soft
stopping performance.

To operate the MVS in low voltage test mode:
1. Isolate the soft starter from the motor and the mains supply.
2. Connect one non-conduction resistor assembly to each phase arm.

For V02, V03 and V04 units:

Clip one end of the resistor assembly to the plated hole on the non-conduction
PCB. The non-conduction PCB is located at the top of the phase arm, behind
the long round grading resistor (on the left hand side when viewed from the
front). Clip the other end of the resistor assembly to any point on the steel
bracket behind the other grading resistor.

Non-conduction

PCB

Non-conduction

resistor assembly

Steel

bracket

Chapter 7

«
...
22
23
24
25
26
...
»

Содержание MVS0080






















































Отзывы:

Нет отзывов

Похожие инструкции для MVS0080

Бренд: Ickle Bubba Страницы: 23

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 36

Бренд: Gatekeeper Страницы: 28

Бренд: Gate Motors Страницы: 6

Бренд: Vacon Страницы: 132

Бренд: OEM Страницы: 8

Бренд: ABB Страницы: 102

Бренд: Quinny Страницы: 21

Бренд: Daihan Scientific Страницы: 11

Бренд: Vertiv Страницы: 2

Бренд: Quantum Страницы: 20

iEP-5000G Series

Бренд: ASROCK Страницы: 2

Бренд: Runxin Страницы: 4

Бренд: Daikin Страницы: 32

Бренд: Valcom Страницы: 9

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды