AuCom MVS0080 Скачать руководство пользователя | Manualshive

Страница: 34 / 53

background image

OPERATION: USER INTERFACE

MVS Series

33

710-03261-00D

•

Signalling Simulation

The MVS Controller allows the user to simulate output signalling in order to confirm
that the outputs are operating correctly.

NOTE

During the simulation, no pre-start checks are made and the soft starter
must be disconnected from mains voltage. The MVS Controller must be
connected to the low voltage control supply.

The simulation is only available when the soft starter is in Ready state.

To activate the signalling simulation:
1. Open the Commissioning Menu and select Signalling Simulation.

Simulation Mode
Output Signal Sim >

2. Press

the

►

button to open the simulation list. The display will indicate the first

simulation in the list.

Analog Output

Simulate

>

3. Use

the

▲

and

▼

buttons to select a simulation. The following signals are

available to simulate:

Analog output
Low current flag

1

High current flag

1

Motor temperature flag

1

Relay A
Relay B
Relay C

1

To test the flags, set an output relay (parameters 5-A to 5-C) to the

appropriate function and monitor the relay's behaviour.

4. Once the required simulation is displayed, press

►

to confirm the selection.

Low Current Flag

Simulate

>

5. Press

the

▲

button to start the simulation. Pressing the

▼

button stops the

signal.

Low Current Flag

▲

On

▼

Off

While the signal is being simulated, the display will indicate On. While the
signal is not being simulated, the display will indicate Off.

6. Once the simulation is complete, press

◄

to return to the simulation list.

Press

▲

or

▼

to select another simulation, or press

◄

again to return to the

Commissioning Menu.

Analog Output Simulation

The analog output simulation uses the

▲

and

▼

buttons to change the analog

output current at terminals B10, B11 of the MVS Controller.

Analog Output
0% 4

mA

Attach an external current measuring device to terminals B10, B11 of the MVS
Controller. Use the

▲

or

▼

button to adjust the percentage value in the lower left

hand corner of the display. The current measuring device should indicate the
same level of current as shown at the lower right corner of the display.

«
...
32
33
34
35
36
...
»

Содержание MVS0080






















































Отзывы:

Нет отзывов

Похожие инструкции для MVS0080

Бренд: Warren Controls Страницы: 16

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: ZKTeco Страницы: 8

Бренд: EasyIO Страницы: 18

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Gate Motors Страницы: 6

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

Бренд: brel-motors Страницы: 2

Бренд: Insignia Страницы: 2

Бренд: Thermomart Страницы: 6

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды