manualshive.com logo in svg

ATTO Technology iPBridge 1550, Инструкция по установке и эксплуатации

Поделиться
Скачать
ATTO Technology iPBridge 1550 Скачать руководство пользователя страница 54

45

 

ATTO Technology Inc. iPBridge Installation and Operation Manual

 7.1.5  SCSI configuration commands

The SCSI ports are configured with default settings but may be customized to your specifications using 
the CLI commands in this section.

SCSIInitID

Specifies the persistent SCSI initiator ID to be used on the 
specified SCSI port. All maps coinciding with the user-
specified SCSIInitID must be set to offline and become 
invalid upon issuing this command. Choices are 0 to 15.

Default: 7
set SCSIInitID [sb [0-15] ]
Requires a SaveConfiguration command
get SCSIInitID

SCSIPortBusSpeed

Controls the transfer rate at which the iPBridge attempts 
to negotiate with its SCSI devices. 

Default: Ultra 160
set SCSIPortBusSpeed [sb [fast | ultra | ultra2 | ultra160 ]
Requires a SaveConfiguration command
get SCSIPortBusSpeed [PortNum]

SCSIPortList

Returns a list of available SCSI ports and their current 
status. Valid status values are 

O.K. 

and 

Failed.

SCSIPortList 

SCSIPortReset

Resets the specified SCSI bus.

 SCSIPortReset [sb]

SCSIPortResetOnStartup

Specifies whether or not the SCSI port is reset on power-
up.

Default: enabled
set SCSIPortResetOnStartup [sb [enabled | disabled] ]
Requires a SaveConfiguration command
get SCSIPortResetOnStartup [sb]

SCSIPortSelTimeout

Indicates the time, in milliseconds, that the bridge waits 
for a response from a SCSI device on the selected port 
after a selection request.

get SCSIPortSelTimeout [sb]

SCSIPortSyncTransfer

Specifies whether synchronous SCSI transfers should be 
negotiated with devices on the specified SCSI port.

Default: enabled
set SCSIPortSyncTransfer [[sb [enabled | disabled] ]
Requires a SaveConfiguration command
get SCSIPortSyncTransfer [sb]

SCSIPortTermination

Configures/reports the SCSI internal termination of the 
SCSI port identified.Enabling termination allows the 
iPBridge to act as a terminator at the end of a SCSI chain.

Default: enabled
set SCSIPortTermination [sb [enabled | disabled]]
Requires a SaveConfiguration command
get SCSIPortTermination [sb]

SCSIPortWideTransfer

Specifies whether wide SCSI transfers should be 
negotiated on the specified bus.

Default: enabled
set SCSIPortWideTransfer [sb [enabled | disabled] ]
Requires a SaveConfiguration command
get SCSIPortWideTransfer [sb]

SCSITargetLUNs

Sets the maximum number of SCSI LUNs per target the 
FibreBridge attempts to query during a SCSI bus scan. 
Choices are 8 and 32.

Default: 8
set SCSITargetLUNs [sb] [8 | 32]
Requires a SaveConfiguration command
get SCSITargetLUNs

SCSITargets

Lists the physical devices connected and running on the 
specified SCSI port. 

SCSITargets [n]

SpeedWrite

When enabled, improves the performance of WRITE 
commands to target devices attached to the iPBridge. 
Specify SCSI bus (sb), target (st), LUN (sl) of a mapped 
SCSI device or (all) for each currently mapped device

set SpeedWrite SCSI [sb st sl | all] [enabled | disabled]
get SpeedWrite SCSI [sb st sl | all] 

Содержание iPBridge 1550









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды