Atlantic Ultraviolet Mighty Pure MP16A, Руководство пользователя, Страница: 13 / 24

13
R
EPLACEMENT OF
B
ROKEN
Q
UARTZ
S
LEEVE
SAFETY EQUIPMENT REQUIRED TO PERFORM TASK
CAUTION: Broken Quartz is SHARP. It is recommended that protective goggles and gloves are worn when handling.
WARNING: Disconnect power to water puri fi er. Shut off water supply to water puri fi er via inlet and outlet shut
off valves. Drain chamber by removing drain plug.
Follow the steps in “ Quartz Sleeve Installation, Cleaning or Replacement ” to remove lamp and quartz sleeve.
1. To prevent damage to the electrical components, it is necessary to separate the ballast housing from the puri fi er chamber.
• On Mighty  Pure
®
Models MP16A, and MP22A, the ballast housing is mounted to the puri fi er chamber using four (4)
No. 8 x 3/8” long screws. Using a Phillips cross point screwdriver, carefully remove the four (4) screws, from along the
sides of the ballast housing, and set aside. Separate the housing from the chamber.
• On Mighty  Pure
®
Models MP36C, and MP49C , the ballast housing is mounted to the puri fi er chamber using four (4)
1/4”-20 x 3/8” long hex head bolts. Using a 7/16” wrench or an adjustable wrench, carefully remove the four (4) bolts
with the lock and
fl at washers, from along the top of the ballast housing, and set aside. Separate the housing from the
chamber.
• Keep ballast housing and mounting hardware in a clean, dry area.
2. Unscrew static gland nuts from each end of the chamber. Remove Te fl on
®
washer and o-ring from both ends of quartz sleeve.
Te fl on
®
washer will sometimes remain within the static gland nut. If so, remove Te fl on
®
washer from static gland nut before
proceeding.
3. CAUTION: Carefully remove as much of the broken quartz sleeve as possible, from each end of the chamber.
4. To remove fragments of quartz sleeve, hold the puri fi er vertically and shake. The quartz fragments will break and drop out
of the puri fi er through the gland fi tting. Flush water through chamber being careful to remove all quartz fragments from the
interior of the chamber.
5. Carefully discard all pieces of the broken quartz sleeve.
6. Align the end of the replacement quartz sleeve with the gland fi tting of the chamber.
7. Carefully slide the quartz sleeve into the chamber guiding it through the gland fi tting. NOTE: Use care to keep the quartz
sleeve parallel to the the chamber. Angling the quartz sleeve in any direction could result in the breakage of the quartz sleeve.
8. As the quartz sleeve nears the far end of the chamber, support the quartz sleeve by inserting your fi nger through the far end
gland fi tting and into the quartz sleeve. This will minimize the possibility of breaking the quartz sleeve as it passes through
the gland fi tting.
9. Center the quartz sleeve in the chamber, making sure the quartz sleeve protrudes an equal distance past each threaded gland
fi tting, of the chamber.
10. Re-install o-rings, Te fl on
®
washers, and static gland nuts. Be sure o-rings are placed on quartz sleeve before Te fl on
®
washer.
Tighten static gland nuts fi rmly by hand only, DO NOT USE HAND TOOLS . Tightening with hand tools is likely to cause
quartz sleeve to break.
11. Re-assemble ballast housing to puri fi er chamber, using hardware removed in Step 1. NOTE: When re-assembling ballast
housing to puri fi er chamber, electrical power cord should exit ballast housing from the end mounted opposite the drain plug.
12. When all connections are complete, allow water to enter the water puri fi er at a low fl ow rate until the puri fi er is full. With the
puri fi er pressurized, it should be checked for leaks.
13. See “ Lamp Installation or Replacement ” section to properly re-install the lamp into the water puri fi e r.