manualshive.com logo in svg

Atkinson Electronics A0217, Руководство пользователя

Поделиться
Скачать
Atkinson Electronics A0217 Скачать руководство пользователя страница 11

www.atkinsonelectronics.com 

             Circuit Board Division 

800.261.3602 

11 

Revised 09/18

 

 

Electric Start High Speed Gas/ Propane Generator with Starter Control Box 

 

This application matches most high speed or portable generator sets that have an electric starter and some type of starter control. 
These  generators  should  have  the  ignition  switch  left  in  the  on  position.  The  start  commands  usually  come  through  the  GSCM 
connected to the remote start terminals. The remote start may be either momentary or maintained. 

 

 

 

The K2 (crank) relay is used to switch the start input which is looking for a momentary signal. The K2 (crank) relay opens when the 
generator  has  reached 30Hz,  or  half  speed.  If  this  setting  doesn’t  allow  the  start  input  to  remain  engaged  long  enough  for  the 
generator  to  stay  on-line,  adjust  the  run  disconnect  setting  to  55Hz.  See  GSCM  INITALIZATON  AND  ADJUSTMENT  for  changing 
adjustments. The K4 (shutdown) relay provides a momentary stop signal until the generator AC Hz has dropped to zero. 

 

The K3 (ignition) relay provides a continuous run signal for 
generators requiring a maintained start signal. The K4 
(shutdown) relay provides a momentary stop signal until 
the generator AC Hz has dropped to zero.

A double pole kill switch wired and installed by the user 
stops the generator instantly in emergency situations such 
as a fuel spill. One switch pole (N.C.) kills power to the 
GSCM opening all relays. The other switch pole (N.O.) 
shorts out the magneto for an instant stop.

Содержание A0217

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды