manualshive.com logo in svg

ATI Technologies Wireless F/T WNet-6, Инструкция по установке и эксплуатации

Поделиться
Скачать
ATI Technologies Wireless F/T WNet-6 Скачать руководство пользователя страница 2

Wireless F/T Installation and Operation Manual
Document #9620-05-Wireless FT-03

Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 USA • Tel: +1.919.772.0115 • Fax: +1.919.772.8259 • www.ati-ia.com • Email: [email protected]  

2

Foreword

Information contained in this document is the property of ATI Industrial Automation, Inc. and shall not be reproduced in 
whole or in part without prior written approval of ATI Industrial Automation, Inc. The information herein is subject to 
change without notice and should not be construed as a commitment of ATI Industrial Automation, Inc. This manual is 

periodically revised to reflect and incorporate changes made to the F/T system.

ATI Industrial Automation, Inc. assumes no responsibility for any errors or omissions in this document.

Copyright © by ATI Industrial Automation, Inc., Apex, North Carolina USA. All Rights Reserved. Published in the USA.

In consideration that ATI Industrial Automation, Inc. (ATI) products are intended for use with robotic and/or automated 

machines, ATI does not recommend the use of its products for applications wherein failure or malfunction of an ATI 
component or system threatens life or makes injury probable. Anyone who uses or incorporates ATI components within 
any potentially life-threatening system must obtain ATI’s prior consent based upon assurance to ATI that a malfunction 
of ATI’s component does not pose direct or indirect threat of injury or death, and (even if such consent is given) shall 
indemnify ATI from any claim, loss, liability, and related expenses arising from any injury or death resulting from use of 
ATI components.

All trademarks belong to their respective owners. 
Windows™ is a registered trademark of Microsoft Corporation. 
MicroSD is a trademark of SD-3C, LLC 

Wi-Fi Direct is a trademark of the Wi-Fi Alliance

Note

Please read the manual before calling customer service. Before calling, have the following 
information available:

1. 

Serial number (e.g., FT01234)

2. 

Transducer model (e.g., Nano17, Gamma, Theta, etc.)

3. 

Calibration (e.g., US-15-50, SI-65-6, etc.)

4. 

Accurate and complete description of the question or problem

5.  Computer and software information. Operating system, PC type, drivers, application 

software, and other relevant information about your configuration.

If possible, be near the F/T system when calling.

How to Reach Us

Sale, Service and Information about ATI products:

ATI Industrial Automation

 

1031 Goodworth Drive

 

Apex, NC 27539 USA

 

www.ati-ia.com

 

Tel: 919.772.0115

 

Fax: 919.772.8259

 

E-mail: 

[email protected]

Technical support and questions:

Application Engineering

 

Tel: 919.772.0115, Option 2, Option 2

 

Fax: 919.772.8259

 

E-mail: 

[email protected]

Содержание Wireless F/T WNet-6



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды