background image

17

18

[Ventilation equipment ] 

To  ensure  safe  and  reliable  operation  of  the  equipment,  the  ambient  temperature 
must  be  within  the  permission  range  –25°C

55°C,  therefore,  appropriate 

ventilation  devices  must  be  equipped  with  to  release  the  heat  generated  by  the 
equipment. We suggest the ventilation rate is more than 3665m³/h.

 

 There must be ventilation equipment inside the distribution room to ensure release 

of  the  waste  heat  generated  by  the  inverter  from  the  equipment,  and  allow  for 
maximum  ambient  environment  temperature.  This  can  be  realized  from  installation 
of exhaust devices;

 

 Another fan can be added at the air duct outlet to exhaust the air out and ensure 

balanced pressure;

 

 The direction of the air outlet shall be selected according to the local actual wind 

direction;

 

 Pay attention to the dustproof measures and waterproof design at the air inlet and 

outlet;

 

 If more air ducts are required, its dimensions shall be designed by the professionals 

according to the air output amount.

[Other protections] 

With IP20 of protection level, inverter is appropriate to be installed in dry and clean 
environment. Meanwhile, water leakage of the house shall be prevented, as it may 
damage  the  inverter.  According  to  EMC  requirement  and  noise  level,  the  inverter 
shall be installed in industrial environment.

4.2 Tools and spare parts required for whole machine installation

Tools and spare parts required for installation is as follows:

  

Hoisting crane, forklift or fork lift truck (with the capacity for bearing the weight of the inverter)

 

 Torque wrench

 

 Screwdriver

 

 Wire stripper

 

 Terminal crimping machine

 

 Heat dryer

  Megger and multimeter

Before  the  inverter  is  moved  to  the  designated  place,  we 
suggest  to  lay  the  DC  input  cable  and  AC  main  power  supply 
cable. As these cables are relatively thick, they are hard to be 
cabled after the inverter is installed.

4.3 Mechanical installation

NOTE:

This inverter is transported as an integrated unit, and the user can hoist it from the 
bottom with a forklift, or move it with a hoisting crane or crane.

Note 1: The inverter is integrated and cannot be dissembled either in transportation 
or  installation.  Any  fault  attributed  to  modification  unauthorized  by  the  ATESS  is 
beyond the quality assurance.

Note  2:  In  movement,  tilt,  violent  shake  or  sudden  force  upon  the  inverter  shall  be 
prevented, such as sudden down of lifting.

Note  3:  Please  read  carefully  the  labeled  parameters  to  select  an  appropriate 
transportation means and storage place.

CAUTION!

To keep the equipment in a better protective status, please adopt transportation with 
package as much as possible, and comply with the labels printed on the package in 
transportation

4.3.1 Transportation of packaged whole machine

We suggest the user make use of forklift to move the inverter if possible.

Sign

Indication

The gravity centre

Lifting logo

Содержание PCS100

























Отзывы: