background image

43

44

Limited Product Warranty 

(Applicable under normal application, installation, use and service conditions) 
ATESS  warrants  the  above  listed  products  to  be  free  from  defects  and/or  failure 
specified for a period from the date of sale as shown in the Proof of Purchase to 
the Original purchaser. 

The  warranties  described  in  these  “Limited  Warranties  ”  are  exclusive  and  are 
expressly in lieu of and exclude all other warranties, whether written, oral, express 
or  implied,  including  but  not  limited  to,  warranties  of  merchantability  and  of 
fitness  for  a  particular  purpose,  use  ,or  application,  and  all  other  obligations  or 
liabilities  on  the  part  of  ATESS  ,  unless  such  other  obligations  or  liabilities  are 
expressly  agreed to it in writing signed and approved by ATESS , ATESS shall have 
no  responsibility  or  liability  whatsoever  for  damage  or  injury  to  persons  or 
property,  or  for  other  loss  or  injury  resulting  from  any  cause  whatsoever  arising 
out of or related to the modules, including, without limitation, any defects in the 
modules or from use or installation. Under no circumstances shall ATESS be liable 
for incidental , consequential or special damages howsoever caused; loss of use, 
loss  of  production,  loss  of  revenues  are  therefore  specifically  and  without 
limitation excluded to the extent legally permissible, ATESS  ’s aggregate liability, 
if  any,  in  damages  or  otherwise,  shall  not  exceed  the  invoice  as  paid  by  the 
customer.

 The “Limited Product Warranties” described above shall not apply to, and ATESS 
shall  have  no  obligation  of  any  kind  whatsoever  with  respect  to,  any  inverter 
which has been subjected to:

— Misuse, abuse, neglect or accident;

— Alteration, improper installation or application;

— Unauthorized modification or attempted repairs;

— Insufficient ventilation of the product;

— Transport damage;

— Breaking of the original manufacturers seal;  

— Non-observance of ATESS installation and maintenance instruction;

— Failure to observe the applicable safety regulations 

— Power failure surges, lighting, flood, fire, exposure to incorrect use, negligence, 
accident, force majeure, explosion, terrorist act, vandalism or damage caused by 
incorrect  installation,  modification  or  extreme  weather  conditions  or  other 
circumstances not reasonably attributable to ATESS. 

The warranty shall also cease to apply if the product cannot be correctly identified 
as the product of ATESS. Warranty claims will not be honored if the type of serial 
number on the inverters have been altered, removed or rendered illegible.

Liability

The liability of ATESS in respect of any defects in its DC inverters shall be limited to 
compliance  with  the  obligations  as  stated  in  these  terms  and  conditions  of 
warranty. Maximum liability shall be limited to the sale price of the product. ATESS 
shall accept no liability for loss of profit, resultant of indirect damage, any loss of 
electrical  power  and  /  or  compensation  of  energy  suppliers  within  the  express 
meaning of that term.
The warranty rights as meant herein are not transferable or assignable to any third 
party excepting the named warranty holder.

8.3 Contact

If you have technical problems concerning our products, contact your installer or 
ATESS. During inquiring, please provide below information:

·

Inverter type

·

Modules information

·

Communication method

·

Serial number of Inverters

·

Error code of Inverters

·

Display of inverters

Содержание PCS100

























Отзывы: