AT&T DLC-100 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 72

AT&T DLC-100 Скачать руководство пользователя страница 48

Glass Break Sensor Features and Operation

Digital Life User Manual

|

Page

38

of

62

ATT-UM-V1.1-201303

Glass Break Sensor Features and Operation

Your Glass Break Sensor (SW-ATT-GB) is a fully monitored sensor that transmits
intrusion alarm information to the DLC-100. It is a tamper protected ceiling- or wall-
mounted unit with a fifteen (15) foot maximum detection range, 360° maximum
horizontal sensing angle, and dual-stage glass break detection, as shown:

Replacing the Glass Break Sensor (SW-ATT-GB) Batteries

CAUTION

: Opening the battery compartment door when the system is armed triggers

the transmission of a tamper alarm to the AT&T Digital Life Central Monitoring Center.
Therefore, in order to prevent a false alarm, please ensure that the system is disarmed
prior to opening the battery compartment door to replace the batteries.

You can replace the battery by turning the sensor counterclockwise from the base.
Replace the two (2) CR123A batteries (Panasonic

®

CR123PT/1FE, GP

®

GPCR123A),

paying careful attention to the battery polarity. Re-attach the glass break detector to its
base, match the alignment marks, and twist clockwise.

«
...
46
47
48
49
50
...
»

Содержание DLC-100









































































Отзывы:

Нет отзывов