background image

 

     A7877F • 800-810-WIRE (9473) • www.sargentlock.com         2

Copyright © 2015, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved. 

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

05/15/15

      

 

  Table of Contents

Warning  ...................................................................................2
General Description .................................................................3
Hardware Specifications .........................................................3
Electrical Specifications ..........................................................3
Parts Breakdown .....................................................................4
Installation Instructions ..........................................................6
Wiring Diagrams ....................................................................14
UL 294 Compliance ................................................................18
Mechanical Operational Check .............................................19
Electrical Operational Check .................................................19

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the inter-
ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
• 

Reorient or relocate the receiving antenna

• 

Increase the separation between the equipment and receiver

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• 

Consult the dealer or an experienced TV technician for help

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.
met. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regula-
tions. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)  
this device must accept any interference received, including interference that may cause undesired operation. 
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des 
règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer 
l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui 
peut causer l’opération peu désirée.

Observe precautions for handling electrostatic sensitive devices.

!

Changes or modifications to this unit not expressly approved by the party  
responsible for compliance could void the user’s authority to operate the equipment.

1

2

3

4

5

6

7

8

9

10

Warning

 

1

!

Содержание Harmony H1





















Отзывы: