Asada BEAVER 50 Скачать руководство пользователя | Manualshive

Страница: 5 / 36

background image

•

Immediately after threading, Dies, chips and threaded surface are hot.
Do not touch them directly with hands.

•

Fix the Carriage to avoid moving while carrying the machine, hold and
lift the bottom of the machine. Do not carry the machine by the scroll
or reamer to carry the machine.

•

When lifting the machine, bend your knees to avoid a load on your waist.

•

The machine stained with threading oil is slippery. Do not drop the
machine on your feet while lifting it.

•

Do not install the machine inclined or on an unstable place. The machine
fall down, causing injury.

•

Do not put the machine with the Die-Head side higher than the machine.
Threading oil leaks from the inside of a pipe, staining the floor.

•

Keep proper footing and balance at all times. You may tumble and get hurt.

•

Do not operate the machine when you cannot concentrate on your work,
e.g. when you are tired or while under the influence of alcohol,
medication or drugs. Otherwise, accident or injury may occur.

•

Before turning on the machine, make sure that hand tools used for
inspection or adjustment are removed from the machine. Accident or
injury may occur if you start the machine with hand tools on it.

•

Use only the accessories and attachments given in this manual and
our catalogs. A failure to do so will lead to accident or injury.

•

Die-Head is wet and slippery with threading oil. Do not drop it on your
feet while replacing.

•

Drinking tap water mixed with threading oil may cause diarrhea or
vomiting. Before laying pipings, always wash off threading oil from
the threaded surfaces and the inside the piping.

•

Always perform pressure test on threaded pipings. Otherwise, leakage
of gas or water may occur.

•

Immediately stop the machine if something is wrong with the machine
or you have noticed unusual smell, vibration, sound, etc. during
operation, and refer to "6. TROUBLE SHOOTING" in this manual and
follow the corresponding instructions.

•

Repair should only be carried out by our sales representative. Otherwise
the machine may not show its performance or you may get injured.
Ask the shop of your purchase or our sales office.

•

Our products are in accordance with the relevant safety rules. Do not
modify them.

High Temperature

4

Other

«
...
3
4
5
6
7
...
»

Содержание BEAVER 50





































Отзывы:

Нет отзывов

Похожие инструкции для BEAVER 50

Бренд: Tanaka Страницы: 20

Бренд: KEENCUT Страницы: 9

Бренд: Elem Garden Technic Страницы: 91

Бренд: Hitachi Koki Страницы: 26

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 32

Бренд: KitchenAid Страницы: 44

Бренд: ITW Signode Страницы: 2

Бренд: Eastwood Страницы: 12

ClassicCut CL100

Бренд: Rexel Страницы: 30

Бренд: 2M2 Страницы: 24

Бренд: Maruyama Страницы: 16

Бренд: Maruyama Страницы: 16

Бренд: EINHELL Страницы: 32

Бренд: EINHELL Страницы: 46

Бренд: GreenWorks Tools Страницы: 16

Бренд: Safety Speed Manufacturing Страницы: 16

Бренд: Partner Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды