manualshive.com logo in svg

Asada BEAVER 50, Инструкция по эксплуатации, Страница: 30 / 36

Поделиться
Скачать
Asada BEAVER 50 Скачать руководство пользователя страница 30

 
 

1-6) Replacement of Carbon Brush 

 
 
 
 
 
 
 
 
 
 
 

 

(1)

 

Drain oil. 

(2)

 

Remove the Die-Head and lay down the machine. 

(3)

 

Unscrew the Under Cover mounting bolts and remove the Under Cover from the machine.

（

fig45

）

 

(4)

 

Turn the cap inside with a flat screwdriver and take out the Carbon Brush. 

（

fig46,47

）

 

 

 

     

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(5)

 Insert a new Carbon Brush. Do not stain the Carbon Brush with oil on fingers, etc. 

(6)

 Install the cap and install the Under Cover with the removed bolts. 

29 

 

       • Disconnect the Power Plug to avoid electric shock. 

 

 

       • Keep the new carbon brush free from oil, dirt, chips, etc. Avoid the stain of   

                gloves from attaching to the Carbon Brush. 

              •

 

A replacement opening is provided on the bottom of this machine. 

        Erect the machine using utmost care not to fall. 

 

 

 

 

〈

46

〉

 

Lay the Machine down

〈

45

〉

 

Under Cover 

cap 

Motor 

〈

47

〉

 

Carbon Brush 

Содержание BEAVER 50





































Отзывы:

Нет отзывов