Asada BEAVER 50 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

Asada BEAVER 50 Скачать руководство пользователя страница 27

1-2) Replacement of Reamer Blade

(1)

Lift the Cutter and Die-Head and pull the Reamer toward you.

(2)

Put out the Spring Pin in the neck of the Reamer Blade.

(3)

The Reamer Blade is detached by pulling the Reamer Holder forward.

(4)

Install a new Reamer Blade.

(5)

Re-insert the removed Spring Pin in the hole of a new Reamer Blade.

1-3) Replacement of Cutter Blade

  (1) Swing the Cutter to upright position and lower the Die-Head.
  (2) Straighten the bend of split pin and pull it upward. (fig.35)
  (3) While holding the Blade, slightly push out the Cutter Blade Set Pin and pull out from the opposite side.
          (fig.36)

(4) Wipe off chips, dirt, oil, etc. from the pin and apply grease to the groove.
(5) Put a new Blade into the Blade Bracket and insert pin.
(6) Insert a new split pin into the Cutter Blade Set Pin, and end the ends.

26

・

Wear gloves when working so as not to cut fingers with the Reamer Blade.

〈

36

〉

〈

35

〉

Cutter Blade

Cutter Blade Set Pin

Wear gloves

Pull out
split pin

Split Pin

«
...
25
26
27
28
29
...
»

Содержание BEAVER 50





































Отзывы:

Нет отзывов