Asada BEAVER 50 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

Asada BEAVER 50 Скачать руководство пользователя страница 14

4. OPERATION

• The following gives a general description of threading work including the pipe cutting.
(1) Prepare for operation. Check threading oil.
(2) Install the work on this machine.
(3) For cutting a work. Pipe Cutter operation and Circular Saw operation are different.
(4) In case of a pipe, ream the inner surface.
(5) Change the size of the thread as required. Please note that the operation method is different in
Beaver Die-Head and Manual Die-Head.
(6) Thread the pipe.
(7) Remove the threaded pipe.

The following describes the contents of the above procedures.

1) Preparing for Operation

1-1)

Checking Threading Oil

• A new machine or a machine not used for a long period of time is coated with rust preventive oil.

Wipe it off with a piece of clean cloth.

              (1) Turn Rack Handle clockwise to move the Carriage to the Chuck side.
              (2) Fill the provided threading oil from the right side of the machine up to the Strainer wire
                    netting. (fig.3)

        (3) Make sure the machine is switched off and plug the Power Plug into receptacle. A two-core
           receptacle must always be grounded.
                (4) Switch on the machine and make sure the threading oil flows from the Die-Head. If proper
                      amount of oil is not discharged, adjust with the Oil Adjust Screw., [Refer to Chapter 5.
           MAINTENANCE & INSPECTION 2-1) Adjustment of Threading Oil Discharge Amount].

Strainer

Rack Handle

Fill Threading Oil

〈

3

〉

13

«
...
12
13
14
15
16
...
»

Содержание BEAVER 50





































Отзывы:

Нет отзывов