Asada BEAVER 10 Скачать руководство пользователя страница 5

 

 

BEAVER  10   

 

 

 

4

 

 

 

 

-Keep proper footing and balance at all times. You may tumble and get hurt. 

-Do not operate the machine when you cannot concentrate on your work, e.g. when 

you are tired or while under the influence of alcohol, medication or drugs. 

Otherwise, accident or injury may occur. 

-Before turning on the machine, make sure that hand tools used for inspection or 

adjustment are removed from the machine. Accident or injury may occur if you 

start the machine with hand tools on it. 

-Use only the accessories and attachments given in this manual and our catalogs. 

A failure to do so will lead to accident or injury. 

-Immediately stop the machine if something is wrong with the machine or you have 

noticed unusual smell, vibration, sound, etc. during operation, and refer to 

"5.TROUBLE SHOOTING" in this manual and follow the corresponding instructions. 

-Repair should only be carried out by our sales representative. Otherwise the 

machine may not show its performance or you may get injured. Ask the shop of 

your purchase or our sales office. 

-Our products are in accordance with the relevant safety rules. Do not modify them.

 

 

 

 

-Do not put the machine or workpiece on the Power Cord. Damaged cord and 

current leakage will occur.

 

 

-Watch the position of your finger while lowering frame to avoid pinching of fingers. 

-Do not leave the machine with a long workpiece set on it. You may tumble and get 

hurt.

 

 

-Securely install accessories in accordance with this manual. Otherwise, accident 

or injury result.

 

 

-Before further use of the machine that is damaged should be carefully checked to 

determine that it will operate properly and perform its intended function. 

-If you have dropped or hit the machine accidentally, carefully check for damage, 

crack or deformation. If the machine is used with such defect, poor cutting 

accuracy, accident and injury can result.

 

 

-Before leaving the machine for a long time, disconnect the Power Plug. 

-The work material with chip is slippery. Do not drop it on your feet. 

-Keep your work bench and area tidy and well lit. Cluttered areas and benches 

invite injuries. 

 

Содержание BEAVER 10

























Отзывы: