Asada BEAVER 10 Скачать руководство пользователя страница 2

BEAVER 10 

 

 

 

Splashing

 

SAFETY PRECAUTIONS 

Thank you for choosing our Band Saw Beaver 10. 

*This Instruction Manual must be retained by the user of this machine. 

*Read this Instruction Manual carefully and completely before use and thoroughly understand the usage, capacity,cautions, 

and easy repairs for correct operation. 

*Handle the machine properly to make full use of its functions for safe work. 

*After reading the instructions, save this manual so that you can read it when necessary. 

*Use the machine for the intended application only. It will do a better job and be safer at the rate for which it was designed. 

*Upon receiving the machine, check the following. 

- Check that the machine is built conforming to the specifications stated in your order. 

- Check the overall machine for any damage or deformation caused in transit due to accidents or other reasons. 

- Check that all items and accessories delivered. 

In case any discrepancy is found, immediately report the fact to the shop you purchased or our sale office. 

(The contents of this manual are subject to change without prior notice.) 

 

 

CLASSIFICATION OF CAUTIONS 

Precautionary signs are classified into the following 3 levels 

 

Indicates an imminently hazardous situation which, if not avoided, will 
result in death or serious injury. 

 
 
                              Indicates a potentially hazardous situation which, if not avoided, could 

result in death or serious injury. 
 
Indicates a potentially hazardous situation which, if not avoided, may 

result in minor or moderate injury. It may also be used to alert against 
unsafe practices. 

SYMBOLS 

                               

       

         

       

                     

   

 

 

   

 

   

     

     

       

 

 

   

 

  

 

 

 

 

Electric 

Shock

 

Cutting 

Blade

 

High Tem- 

perature

 

Rotation 

parts

 

Instruction 

manual

 

Other

 

Earth

 

Falling

 

Fire

 

Explosion

 

Mask

 

Pinching

 

Dragging

 

Содержание BEAVER 10

























Отзывы: