manualshive.com logo in svg

Arturia beatstep pro, Руководство пользователя

Поделиться
Скачать
Arturia beatstep pro Скачать руководство пользователя страница 44

44 

ARTURIA – BeatStep Pro – USER’S MANUAL 

sensitivity of the pads to perform volume swells on the selected drum during the 
roll. 

•

 

When  SEQ1,  SEQ2  or  DRUM  are  selected  the  strip  functions  as  a  Looper.  It  will 
loop  a  certain  section  of  the  music  based  on  the  position  of  your  finger  on  the 
strip. It affects all three sequencers at the same time. 

6.6.1

 

Roller mode 

The Roller functions exclusively in Control Mode. Since the pads are set to transmit MIDI 
notes by default you should be able to try it immediately. 

But  the  MIDI  Control  Center  can  configure  the  pads  to  send  other  types  of  MIDI 
messages, so it’s important to know that the Roller will only work with pads that are set 
to  NOTE  or  MIDI  CC.  For  example,  it  won’t  use  a  pad  to  transmit  the  same  Program 
change command repeatedly. 

Here are some other things to know about the Roller: 

6.6.1.1

 

General operation 

The Roller will repeat a pad based on a combination of the clock source, the time division 
and the position of your finger on the Roller strip. 
The output will be based on 4/4 time, too. So if your song has a bar of 7/8 and you have 
your finger on the strip at 1/4, the Roller output will be off by an eighth note after that 
bar. 

6.6.1.2

 

Sync settings 

The  Roller  will  work  even  when  an  external  sync  source  is  used.  The  results  may  vary 
depending on the source, though. 

If  playback  is  stopped  and  no  external  clock  is  being  received,  the  Roller  will  output 
notes at a rate based on the internal clock setting. 

If the Time Division is set to TRIPLET, then the roller will playback in triplet beats.

 

6.6.2

 

Looper mode 

Select  SEQ1,  SEQ2  or  DRUM  and  the  strip  enters  Looper  mode.  It  controls  all  three 
sequencers at the same time, so it doesn’t matter which one is selected. 

The  Looper  function  allows  you  to  alter  the  playback  of  the  Project  in  real  time.  It  will 
generate smaller loops based on where you touch the Looper strip and when you do it. 

6.6.2.1

 

Loop length 

The length of the loop is determined by the placement of your finger on the Looper strip, 
with  1/4  being  the  largest  loop  and  1/32  being  the  smallest.  Changing  the  location  of 
your finger changes the size of the loop. 

6.7

 

TRNS LNK 

The  TRNS  LNK  button  allows  both  SEQ1  and  SEQ2  to  transpose  together  by  the  same 
amount. The Drum sequencer will not be affected. 

There are three potential sources for transposition commands: 

•

 

Note data from the MIDI In connector 

Содержание beatstep pro






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды